<font color='black' size='2' face='arial'><FONT face="Arial, Helvetica, sans-serif"></FONT>

<div><br>
<STRONG>OOOPS AGAIN,</STRONG></div>


<div><STRONG></STRONG> </div>


<div><STRONG>THAT IS VR-<U>2</U>000'S   SORRY TED, AOL MUST HAVE LEFT THE 2 OFF. HI</STRONG></div>


<div><STRONG></STRONG> </div>


<div><STRONG>GK</STRONG></div>


<div><br>
</div>


<div style="CLEAR: both"></div>
<br>
<br>


<div style="FONT-SIZE: 10pt; COLOR: black; FONT-FAMILY: helvetica,arial">-----Original Message-----<br>
From: georgenann@aol.com<br>
To: don.adamson@herobroadcasting.com; quadlist@quadvideotapegroup.com<br>
Sent: Wed, Feb 3, 2010 1:27 pm<br>
Subject: Last of the VR-000's<br>
<br>


<div id=AOLMsgPart_2_974efc81-7537-403c-ba9e-acd84b016fe0><FONT face=arial color=black size=2>

<div style="FONT-SIZE: 10pt; COLOR: black; FONT-FAMILY: helvetica,arial">

<div id=AOLMsgPart_2_9405d300-e4f9-4352-95e5-9cdad9d5195b><FONT face=arial color=black size=2>

<div><FONT face="Arial, Helvetica, sans-serif"></FONT>With the recent talk about tubes (Fire Bottles) in VTR's it reminded me of some experience I had with the last of the CBS VR-2000's.</div>


<div> </div>


<div>Since I was the only person maintaining them and occasionally operating them (The regular ops wouldn't go near them) I thought I would make life a little easier for myself.</div>


<div> </div>


<div>First I removed the side panels so I could get into them easier, even though they were between 2 racks.  I did some work on them and came back a few days later and the panels were gone.  Someone stole them.  I never found them in the following years.  But that is OK, it just made it easier to clean, etc. them.</div>


<div> </div>


<div>I figured that since there would be no more recordings made on them, I pulled out all of the tubes in the RAPA's.  This was an all day job because of all the screws Ampex put in them.</div>


<div> </div>


<div>Now the whole RAPA housing was nice and cool and I could get rid of the fan on top of it, thereby not pulling schmutz thru it and no need to change the filter under it.</div>


<div> </div>


<div>I then pulled out the AFA audio keying mods which were there, no need to keep them around either.</div>


<div> </div>


<div>I also wanted to eliminate the Editor, Editec and VHO, but didn't have the "Dummy Plug" which came with the machine which would enable me to do so.  I found I could just pull the boards out of the Editor, but had to leave the chassis in and I had to leave the boards in the Editec, but I have saved some heat in the machine to some degree.</div>


<div> </div>


<div>I also pulled out the full erase chassis, just to make more room.</div>


<div> </div>


<div>While I was at it I went across the street to Archives and pulled the record board out of the RAPA on the AVR-1's, pulled the erase chassis and the boards out of the time code reader and killed the power supply for the Nixie display.</div>


<div> </div>


<div>I was going to jumper out all of those IBM relays behind the control panel in the AVR-1's since there is no need for remote,so I could throw them out also, as they tend to be a constant problem, there were no spares, but ran out of time, bur recommended it be done, I'm sure the guys jumped right into it. (Right!)</div>


<div> </div>


<div>DE</div>


<div> </div>


<div>George Keller<br>
<br>
</div>


<div style="CLEAR: both"></div>
</FONT></div>
</div>
</FONT></div>
<!-- end of AOLMsgPart_2_974efc81-7537-403c-ba9e-acd84b016fe0 --></div>
</font>